Forum Donations
Search
VTF Google Search
 Click Here

questions about xv700 to xv1000 engine swap.

Everything about swapping a motor on your Virago.
  • Advertisement

Post a reply

questions about xv700 to xv1000 engine swap.

PostAuthor: motorlou » Sat Aug 10, 2019 9:52 pm

hey guys just had a question about swapping out a 700 to 1000 engine (both 1985). i want to know the differences in the tci unit. besides timing curves, i read you are supposed to use the pressure sensor from the 1000 along with its cdi. what is this sensor? where is it located. what does it sense?. on the xv1000 tci there are a few extra pins than the xv700. one for the kickstand relay(black/white) then there are red/white, black/red, and black/yellow that go to the said pressure sensor. can the sensor be bypassed? if so how? can an xv1000 tci be used on the 700 or vice versa?

motorlou
Junior Membership
Junior Membership
 
Posts: 39
Joined: Sat Sep 01, 2018 11:49 pm
  Flag
Bike year & model: 1985 virago xv700 and 1985 virago xv1000
Sex: Male

Re: questions about xv700 to xv1000 engine swap.

PostAuthor: Flyingdog » Sun Aug 11, 2019 12:40 am

About the pressure sensor..just another one of those EPA demanded parts, so the bikes could be sold in US..or any other place having emission regulations. It'll be located sitting ontop of the coil cover. During deceleration, it will pull vacuum and retard timing abit. Eliminating some backfiring. IMO: bout as worthless as the MCV/AIS, or any other emission garbage. And..yes..can be eliminated if it don't work or you just don't want it. Some will say it's needed. That's cool, but I say if it is, it's usually to masked something else. But that's just "my" side. Haven't had one on the 1000 since the 80s. Never a problem. I just removed/plug the vacuum hose at the "source" and clip the wire. Been soo long, don't remember how far back I clipped it. Probly at the TCI. If you look at bikes thru out the years, you'll notice how they (Yamaha in this case) kept adding things to eliminate problems pop'n up. Mainly..back fires. All this stuff cropped up, when the "save the earth" movement came to full swing. Think it was around the time hair spray was kill'n the ozone... :bg: Certain years got the MCV, some AIS, some deceleration valves on Mikuni carbs...some a combo of everything. All-in-all..I look at it as anything extra put on a carb..usually ( I say usually) will give ya fits sooner or later.

#36---> https://www.yamahapartshouse.com/oempar ... ectrical-1
User avatar
Flyingdog
Silver Membership
Silver Membership
 
Posts: 2668
Joined: Fri Jun 23, 2017 2:31 am
Location: Colorado Flag
Bike year & model: 1985 xv1000 Virago
1981 xv750 Virago
Sex: Male

Re: questions about xv700 to xv1000 engine swap.

PostAuthor: motorlou » Sun Aug 11, 2019 1:59 am

thanks for the chime. this being said, i believe i can use either tci in either motor. i cant see any differences in the engines except bigger displacements? the pick up coils even look the same (other than the pin connectors being in different positions at the tcis i think i like the 700 tci better because it just has less pins to deal with. i use my bike to commute everyday so i cant just begin swapping stuff on it. but i definately want to answer these oddball questions i have about electrical parts interchangeability.

motorlou
Junior Membership
Junior Membership
 
Posts: 39
Joined: Sat Sep 01, 2018 11:49 pm
  Flag
Bike year & model: 1985 virago xv700 and 1985 virago xv1000
Sex: Male



Post a reply


  • Advertisement

Return to Virago Help - Motor Swap

Who is online

Registered users: KADD256